veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill

veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill

Rotary drum dryer is the device that is used to heat and dry the materials. Rotary drying machine is generally applicable to granular materials and it can be also used for the drying of some part of sticky pasty materials or the materials with high water content. Rotary dryers are commonly used to dry sand, slag, slime and so on. What is more, the drying machine is one of the drying apparatus typically used in the cement plants, namely, cement rotating dryer.In our company, this series applies the new type scatter plate device; it can guide direction, flow on an average and scatter the material and so on. And it can make the material in the thin, average and complete condition. Contact the heat airflow completely and use the heat energy fully. Moreover, it adopts reasonable operational parameter, and compared with general drier, it reduce the coal and power consumption above10-15%,and increase the output above10-15%. At present, it is widely used in cement and mining

Applicatio of veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill:

Chemical industry: ammonium sulfate, sodium sulphide, ammophos, ammonium nitrate, carbamide, oxalic acid, potassium dichromate, PVC, nitrophosphate fertilizer, calcium magnesium phosphate, compound fertilizer,food industry: Glucose,salt, granulated sugar, vitamin malted milk, Granular sugar,minerals: Bentonite, Titanium concentrate, coal, manganese ore, pyrite, limestone, peat. Others: Iron powder, flat soybean, garbage abrasive, match sticks, wood chips, vinasse, etc.

veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill

Working Principle of veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill:

It mainly consists of revolution body, raise material board, transmission device, supportive device and sealing ring, etc.

The heat sources of the drier is from the combustion train, and is adopts down-flow heating methods. When the materials enter into the body from the feeding device, it will be pushed back by the spire raising board. As the drier is in an inclined position, the materials will be down to the lower end under the infveneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball millce of gravity and rotation, but the raising board will be threw to the upper end for scattering. This procession makes the material well-distributed in the body, and then ensure the heat exchange with the heat wind. After repeated cycle with this procession, the moisture content will be dried.

Features and Benefits of veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill :

1. Reasonable design of raising board and angle ensure the material well-distributed and dry with less times, it has reliable operation and high energy utilization ratio, simple maintenance.
2. Adopt an adjustable center tug structure, the good cooperation of the tug and the rolling ring reduce the attrition and energy consumption.
3. The special structure of the dam-wheel decrease the horizontal thrust, when the machine working in inclination station, it has strong ability of anti-overloading, steady operation and high reliability.
4. High temperature resistance, it can use the high temperature to dry the material quickly,
5. Large capacity, few fuel consumption, low drying cost.

veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill

Main Technical Parameters of veneer roller dryer machine /drum for drying flakes /small wet and dry laboratory cement ball mill :

Gypsum drying/stillage dryer/dry grinding mill

Notice of Installation of Dyer Machine

Before the installation of the dryer equipment, the place and the devices to be installed must be checked, in order to avoid other problems during the installation. The check should be made in the positional deviation of the pouring quality and size of the base concrete. The appearance should be clean without pollution, dust or sundries, The basic size and position of deviation shall meet the following requirements: the position between the size of appearance and the basic coordinates. The error between the vertical and the horizontal axis should be less than 20mm, with the different plane elevation errors less than 20 mm; the error size of inclination should be less than 20mm. Remove the protective coating when packing, dusting, greasing, corroding and so on. Check the breakdown and deformation caused in the transportation process of loading and unloading damage. Pre-check and pre-install the components to avoid the rework during the installation and ensure the progress and quality of installation.

1. Pre-sale services:

1>. Select proper equipment model;

2>. Design and manufacture products according to clients' special requirement;

3>. Arrange for visiting our factory, assist them to handle relative procedure, such as visa.

2. Services during the sale:

1>. Make sure goods prepared within delivery time;

2>. Pre-check and accept products ahead of delivery;

3>. Prepare documents required to help customer pass customs clearance.

4>. Help clients to make Project evaluation and feasibility analysis and draft solving plans.

3. After-sale services:

1>. Assist clients to prepare for the first construction scheme;

2>. Install, debug and examine the equipment;

3>. Train technical personnel the first-line operators;

4>. Provide technical exchanging

5>. Offer spare parts at a best price for long term.

Note: Responsible for handling other required matters conforming the state regulations.

Our company, Shanghai Minggong Heavy Equipment CO., Ltd, is a joint-stock enterprise integrating R&D, manufacturing and marketing in Shanghai China. Founded in 1956, we have a long history of producing industrial plants and mining equipment suitable for extracting metals such as, iron, zinc, copper and gold.

Our company covers an area of 40,000 square meter, has a total asset of 150 million CNY and has more than 200 staff including 42 engineers in a scientific research group and 106 technicians in a well-trained riveter and welder team .Our company has a long-term cooperation with many research institutions in China and aboard,bringing in advanced technology of the world.

Our product range includes large-sized rotary kilns, ball mills, cement/lime production plants and AAC plants and primary & secondary crusher as well. These items can be customized for use in different regions, environments and landscapes.

We have ISO9001:2000 and EU CE certificate, and also the equipment for quality control, welding inspection and spraying craft etc. We also have good service before sales, among sales and after sales.

That's why we have customers around the world, including in South America, South Africa, Russia & Asia. Russia, Japan, Australia, Korea, Myanmar, Indonesia, Iran, Chile, Mali, Guinea, Tanzania, Nigeria, Philippines, Bangladesh, Cuba, and Uzbekistan ,etc.